电焊机接线的七个步骤_新闻中心_螺柱焊机|逆变螺柱焊机|电弧螺柱焊机|逆变焊机|-济南金佳源焊接设备秒速赛车-网站秒速赛车
产品分类
全国服务热线
新闻中心 > 新闻中心 秒速赛车>> 新闻中心 > 电焊机接线的七个步骤
电焊机接线的七个步骤
添加时间:2017-10-09 09:30:17

电焊机接线的七个步骤
Seven steps of welding wire
1.选一根绝缘良好的引出线与焊把线(电焊钳引线)可靠连接,接头要拧紧,使其接触良好,防止过热,并用绝缘胶布将接头裸露导体包扎数层使其绝缘良好。螺柱焊机
1. Choose a good lead and insulation holder line (welding clamp wire) reliable connection, connection to tighten, make its good contact, to prevent overheating, and insulating tape round joint bare conductor layers of insulation is good.
2.将引出线敷设至电焊机处并接于焊机二次侧接线柱上,应压紧螺丝使其牢固接触良好,禁止使用缠绕法连接。敷设引出线时避免焊把特别是接头从有水的地方经过,必要时应架空。焊把线经过金属栏杆或扶梯时,应用绝缘性能良好的细绳将其悬挂。
2. Will lead to welder welding place and laying secondary side terminal, should compression screw make solid contact is good, its banning the use of the winding connection. When laying lead holder especially joint from the place where there is water, should be raised when necessary. Holder line with metal railings or escalator, the application of insulation string to hang it.
3.将电焊机金属外壳可靠接地。即:用一根导线一端接至接地网,另一端连接在焊机外壳标有接地标记的螺丝上并拧紧,使其可靠接地,防止外壳带电造成触电事故。
3. The welding metal shell and reliable grounding. : one end with a wire connected to ground net, the other end connected to the welding machine shell with grounding mark and screw down the screws, make its reliable grounding, prevent shell charged cause accident getting an electric shock.
4.将电源线接至电焊机一次侧接线柱,压紧螺丝使其牢固接触良好,禁止使用缠绕法连接。
4. A side terminal connected to the power cord to electric welding machine, compression screw to make it solid contact is good, it is prohibited to use winding connection.
5.将电源线、焊把线的接头及绝缘老化破损处用绝缘胶布包扎,导线绝缘严重老化者禁止使用,裸露的接线柱应加护罩,防止误碰发生触电事故。
5. The joint of the power cord, holder and insulation aging lesions with insulating tape bandage, banning the use of wire insulation ageing, exposed terminal should add cover, prevent touch the electric shock accident by mistake.
6.检查带熔丝的电源闸刀或带熔断器的断路器是否在断开位置,将电源线接至电源开关熔丝或熔断器下侧,严禁带电接线。
6. Check with the power of the fuse knife or fuse circuit breaker is in off position, connected to the power cord to a power supply switch fuse or fuse underside, electrical wiring is forbidden.
7.再次对所接电源线、引出线、外壳接地线进行仔细检查,确认无误后合上电源开关,合开关时应戴绝缘手套且另一只手不得触摸焊机。
7. Once again to connect the power cord, lead wire, ground wire to check carefully, after close the power switch, the switch the insulating gloves should be worn and another hand must not touch welding machine.


北京赛车官网投注平台 上海11选5走势图 秒速赛车 秒速赛车2018 秒速赛车 秒速赛车开奖 北京赛车pk10玩法 北京赛车高频开奖记录 秒速赛车官方网站 北京赛车官网投注平台